If you liked the way your 2008 Toyota Highlander rode and handled when it was new, you can experience the feeling again with our replacement suspension parts. Toyota Parts; Toyota Auto Parts Tell Us More About Your Toyota. View all makes AutoZone carries hundreds of thousands of parts and accessories. Select your Year, Make, Model and Engine to find those that fit your vehicle. See all in Toyota Suspension, Steering, Tire And Wheel. Toyota Shock/Strut - Front.
Hola necesito el manual del diagrama de las cadenas de tiempo de toyota avanza 2008 1.3 porfavor. Jorge luis cabrales hernandez said. O manual de partes de piezas del toyota tercel twin cam. Desde ya muchas gracias. Necesito el diagrama de la suspension trasera del honda civic 2000 exr 4 ptas para poder ver los bujes y poder. View and Download Toyota 2002 HIGHLANDER user manual online. Automobile Toyota 2008 Matrix Owner's Manual. Remember all Toyota parts are de- jack.
Toyota Highlander Service Manual / Front suspension / Front wheel alignment
ADJUSTMENT
1. INSPECT TIRE (SEE PAGE 26-7 )
2. MEASURE VEHICLE HEIGHT
Vehicle height:
Measuring points:
A: Ground clearance of front wheel center B: Ground clearance of lower suspension arm No.2 bush set bolt center
C: Ground clearance of strut rod set bolt center D: Ground clearance of rear wheel center
NOTICE: Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
HINT: Bounce the vehicle at the corners up and down to stabilize the suspension and inspect the vehicle height.
3. INSPECT TOE-IN
Toe-in:
If the toe-in is not within the specified range, adjust it at the rack ends.
4. ADJUST TOE-IN
Cannot get download for ford sync updates. (a) Remove the rack boot set clips.
(b) Loosen the tie rod end lock nuts.
(c) Turn the right and left rack ends by equal amounts to adjust the toe-in.
HINT: Try to adjust the toe-in to the center of the specified value.
(d) Make sure that the lengths of the right and left rack ends are the same.
Rack and length difference: 1.5 mm (0.059 in.) or less (e) Torque the tie rod end lock nuts.
Torque: 74 N*m (755 kgf*cm, 55 ft*lbf) (f) Place the boots on the seats and install the clips.
HINT: Make sure that the boots are not twisted.
(g) Perform VSC system calibration (see page 05-765 ).
5. INSPECT WHEEL ANGLE
(a) Turn the steering wheel fully left and right to measure the turning angle.
Wheel turning angle:
If the right and left inside wheel angles differ from the specified value, check and adjust the right and left rack end lengths.
6. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION
(a) Put the front wheel on the center of the alignment tester.
(b) Set the camber - caster - kingpin gauge at the center of the axle hub or drive shaft.
Camber, caster and steering axis inclination:
If the caster and steering axis inclination are not within the specified values after the camber has been correctly adjusted, recheck the suspension parts for damage and/or wear.
7. ADJUST CAMBER
NOTICE: Inspect toe-in after the camber has been adjusted.
(a) Remove the front wheel.
(b) Remove the 2 nuts on the lower side of the shock absorber.
HINT: When removing the nuts, keep the bolts from rotating.
(c) Clean the installation surface of the shock absorber and the steering knuckle.
(d) Temporarily install the 2 nuts.
(e) Fully push or pull the front axle hub in the direction of the required adjustment. Hyundai usa navigation update download.
(f) Tighten the nuts.
Torque: 230 NVm (2,350 kgfVcm, 170 ftVlbf) HINT: When installing the nuts, keep the bolts from rotating and then torque the nuts.
(g) Install the front wheel.
Torque: 103 N*m (1,050 kgf*cm, 76 ft*lbf)
NOTICE: Keep the bolts from rotating and torque the nuts.
(h) Install the front wheel.
Torque: 103 NVm (1,050 kgfVcm, 76 ftVlbf) (i) Check the camber.
If the measured value is not within the specified range, calculate the required adjustment amount using the formula below.
(Camber adjustment amount) = Center of the specified range medium - Measured value
Check installed bolts combination. Select appropriate bolts from the table below to adjust the camber to within the specified range.
Table (1) (Move the axle toward positive side)
Selected Bolt Combination Citroen repair manual free download.
Bolt Distinguishing Mark
The body and suspension may be damaged if the camber is not correctly adjusted according to the above table.
NOTICE: Replace the nut with a new one when replacing the bolt.
(j) Repeat the steps mentioned above. At step (b), replace 1 or 2 selected bolts. https://factsrenew.weebly.com/blog/itool-radar-bmw-download.
HINT: Replace one bolt at a time when replacing 2 bolts.
Table (2) (Move the axle toward negative side)
Toyota Highlander Hybrid
Selected Bolt Combination
La Suspension De Atras Toyota Highlander 2008 Manual Partes En
Bolt Distinguishing Mark
La Suspension De Atras Toyota Highlander 2008 Manual Partes Se
The body and suspension may be damaged if the camber is not correctly adjusted according to the above table.
NOTICE: Replace the nut with a new one when replacing the bolt.
(k) Repeat the steps mentioned above. At step (b), replace 1 or 2 selected bolts.
Toyota Highlander 2014
HINT: Replace one bolt at a time when replacing 2 bolts.
Shock absorber ASSY front LH..More about Toyota Highlander:
Washer fluid
If any washer does not work or the warning message appears on the multi-information display, the washer tank may be empty. Add washer fluid. Warning When adding washer fluid Do not add washer fluid when the engine is hot or running as washer fluid contains alcohol and ma ..
В© 2011-2019 Copyright www.tohighlander.com
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |